C95400
Home > C95400
C95400
The aluminum bronze C95400 is also called C954. It is the most popular and all purpose high yield aluminum bronze alloy with high tensile strength, ductility, welding ability, and resistance to wear, fatigue, and deformation under shock or overload. The alloy is used while manufacturing bearings, gears, valve components, wear-plate, and wear-strip in conformation with continuous cast specification ASTM B505 and centrifugal cast specification ASTM B271.
Typical Uses for C954 Aluminum Bronze:
Automotive: Weld Guns
Fasteners: Nuts, Large Hold Down Screws
Industrial: Pickling Hooks, Bearings, Pawl, Worm Gears, Machine Parts, Spur Gears, Heavily Loaded Worm Gears, Pump Parts, Landing Gear Parts, Valve Bodies, Valve Guides, Valve Seats, Bearing Segments for the Steel Industry, Pressure Blocks for the Steel Industry, High Strength Clamps, Bushings, Valves, Gears
Marine: Ship Building, Covers for Marine Hardware
Ordinance: Government Fittings
CHEMICAL COMPOSITION
| Al | Cu | Fe | Mn | Ni | |
| Min/Max | 10.0-11.5 | 83.0 min | 3.0-5.0 | 0.5 | 1.5 |
| Nominals | 10.8000 | 83.2000 | 4.0000 | – | – |
IS 3091 : 1999 Chemical Composition:
| Al | Cu | Fe | Mn | |
| Min/Max | 9.0 – 11.0 | Balance | 4.0-5.0 | 0.1 to 0.5 |
IS 3091 : 1999 Tensile Properties:
| Tensile Property | Minimum Requirement |
| 0.2 percent permanent set proof stress | 250 MPa |
| Tensile strength | 600 MPa |
| Elongation on 50 mm guage length | 15 Percent |
Fabrication
| Joining Technique | Suitability |
| Brazing | Good |
| Coated Metal Arc Welding | Good |
| Gas Shielded Arc Welding | Good |
| Machinability Rating | 60 |
| Oxyacetylene Welding | Not Recommended |
| Soldering | Good |
Physical Properties
| Product Property | US Customary | Metric |
| Coefficient of Thermal Expansion | 9.0 ·10-6 per oF (68-572 F) | 16.2 ·10-6 per oC (20-300 C) |
| Density | 0.269 lb/in3 at 68 F | 7.45 gm/cm3 @ 20 C |
| Electrical Conductivity | 13 %IACS @ 68 F | 0.75 MegaSiemens/cm @ 20 C |
| Electrical Resistivity | 80.2 ohms-cmil/ft @ 68 F | 13.33 microhm-cm @ 20 C |
| Magnetic Permeability (As Cast) | 1.27 | 1.27 |
| Magnetic Permeability (TQ50 temper) | 1.2 | 1.2 |
| Melting Point – Liquidus | 1900 F | 1038 C |
| Melting Point – Solidus | 1880 F | 1027 C |
| Modulas of Elasticity in Tension | 15500 ksi | 107000 MPa |
| Specific Gravity | 7.45 | 7.45 |
| Specific Heat Capacity | 0.1 Btu/lb/oF at 68 F | 419.0 J/kg · oK at 293 K |
| Thermal Conductivity | 33.9 Btu · ft/(hr · ft2·oF)at 68F | 58.7 W/m · oK at 20 C |
Sizes Available
| ROUND RODS | 8mm To 70 mm |
| HEX | 10mm To 60mm |
| SQUARE | 10mm To 60mm |
| FLAT | 10mm Min Thickness and max Width 120mm |
| BILLETS | Up to 200 mm |
| INGOTS | As per Specification |
C95400
The aluminum bronze C95400 is also called C954. It is the most popular and all purpose high yield aluminum bronze alloy with high tensile strength, ductility, welding ability, and resistance to wear, fatigue, and deformation under shock or overload. The alloy is used while manufacturing bearings, gears, valve components, wear-plate, and wear-strip in conformation with continuous cast specification ASTM B505 and centrifugal cast specification ASTM B271.
Typical Uses for C954 Aluminum Bronze:
Automotive: Weld Guns
Fasteners: Nuts, Large Hold Down Screws
Industrial: Pickling Hooks, Bearings, Pawl, Worm Gears, Machine Parts, Spur Gears, Heavily Loaded Worm Gears, Pump Parts, Landing Gear Parts, Valve Bodies, Valve Guides, Valve Seats, Bearing Segments for the Steel Industry, Pressure Blocks for the Steel Industry, High Strength Clamps, Bushings, Valves, Gears
Marine: Ship Building, Covers for Marine Hardware
Ordinance: Government Fittings
CHEMICAL COMPOSITION
| Al | Cu | Fe | Mn | Ni | |
| Min/Max | 10.0-11.5 | 83.0 min | 3.0-5.0 | 0.5 | 1.5 |
| Nominals | 10.8000 | 83.2000 | 4.0000 | – | – |
IS 3091 : 1999 Chemical Composition:
| Al | Cu | Fe | Mn | |
| Min/Max | 9.0 – 11.0 | Balance | 4.0-5.0 | 0.1 to 0.5 |
IS 3091 : 1999 Tensile Properties:
| Tensile Property | Minimum Requirement |
| 0.2 percent permanent set proof stress | 250 MPa |
| Tensile strength | 600 MPa |
| Elongation on 50 mm guage length | 15 Percent |
Fabrication
| Joining Technique | Suitability |
| Brazing | Good |
| Coated Metal Arc Welding | Good |
| Gas Shielded Arc Welding | Good |
| Machinability Rating | 60 |
| Oxyacetylene Welding | Not Recommended |
| Soldering | Good |
Physical Properties
| Product Property | US Customary | Metric |
| Coefficient of Thermal Expansion | 9.0 ·10-6 per oF (68-572 F) | 16.2 ·10-6 per oC (20-300 C) |
| Density | 0.269 lb/in3 at 68 F | 7.45 gm/cm3 @ 20 C |
| Electrical Conductivity | 13 %IACS @ 68 F | 0.75 MegaSiemens/cm @ 20 C |
| Electrical Resistivity | 80.2 ohms-cmil/ft @ 68 F | 13.33 microhm-cm @ 20 C |
| Magnetic Permeability (As Cast) | 1.27 | 1.27 |
| Magnetic Permeability (TQ50 temper) | 1.2 | 1.2 |
| Melting Point – Liquidus | 1900 F | 1038 C |
| Melting Point – Solidus | 1880 F | 1027 C |
| Modulas of Elasticity in Tension | 15500 ksi | 107000 MPa |
| Specific Gravity | 7.45 | 7.45 |
| Specific Heat Capacity | 0.1 Btu/lb/oF at 68 F | 419.0 J/kg · oK at 293 K |
| Thermal Conductivity | 33.9 Btu · ft/(hr · ft2·oF)at 68F | 58.7 W/m · oK at 20 C |
Sizes Available
| ROUND RODS | 8mm To 70 mm |
| HEX | 10mm To 60mm |
| SQUARE | 10mm To 60mm |
| FLAT | 10mm Min Thickness and max Width 120mm |
| BILLETS | Up to 200 mm |
| INGOTS | As per Specification |